Clik here to view.
Re: WDTH_CAP problem with BF518
Hello,I am testing different configurations of timer6:*pTIMER6_CONFIG = (WDTH_CAP) | (TIN_SEL) | (PULSE_HI) | (IRQ_ENA) | (PERIOD_CNT);and I configured it to use interrupt priority...
View ArticleRe: Re: Problems obtaining output on the BF527 LCD for LCDColorBar example
Hi Ram, I've asked our hardware team for the expected values at TP18 and TP19, we'll get back to you shortly with these. The section of the EZ-Kit manual you reference above is for the Audio Interface,...
View ArticleCEC-HDMI support in V4L2
Does V4L2 provide any support for CEC in HDMI device?Can we uses the V4l2 subdev driver(from analogdvicesinc github) and implement CEC?
View ArticleRe: OpenCV library on bf609-ezkit
Hi Hichem, could you share us more detailed information about what kind of visual/graphic function you want to support from your product, so we can work together to figure out a reasonable combination...
View ArticleRe: CEC-HDMI support in V4L2
Hi, Currently (Linux version 3.15) there is no CEC support in the upstream kernel. But there is work in progress development on adding support for CEC to the V4L framework. The source code for this can...
View ArticleRe: What is the correct syntax to get CCES v1.1.0 cldp to verify?
Hi Matt, You need to add the "-cmd compare ..." command to your command line. For example:cldp -emu 1000 -proc ADSP-BF524 -driver "C:\temp\cldp\bf524_m25p32_dpia.dxe"-cmd prog -erase affected -format...
View ArticleRe: SHARC Hardware anamoly
Hi Krishna, I have moved your question from the Processors and DSP community to the SHARC Processors community. Please continue the discussion here. Regards,Craig.
View ArticleRe: SHARC Hardware anamoly
Hi Krishna, The anomaly 15000016 has been fixed in Si Rev 0.2.This information can be found in the ADSP-2148x Anomaly list which can be downloaded from the following link.IC Anomalies | SHARC...
View ArticleClik here to view.
Re: Custom device programmer driver for AT25256B and cldp
Hi Sebastien, It sounds as though you may already be familiar with how to run the Driver as a standard application, but just in case, I have written up some information below. You say the program is...
View ArticleRe: Re: Re: Weighing Scale Design
Hi Ragavendra, Basing from your Block Diagram I just need to confirm if the 5V of the USB goes directly to the AVDD pin of the ADuCm360? Please note that the ADuCM360 has an absolute maximum...
View ArticleAD9361 Change BW
Dear sir: I want to change different Bandwidth (like LTE 5MHz to LTE 10MHz) in the running time, the procedure may beTx state ->reset->change BW ->Tx stateIf we follow the procedure as above,...
View ArticleRe: PVP in BlackFin BF609
Hi Bill,THC block cannot process selective pixels. It can however process pixels within a region or outside a region (ROI). I think what you are looking for is to process only 1 of several channels....
View ArticleAD9361 initialization and calibration
hey guys. I work on AD9361 with my XILINX-V6AD9361 initialization needs calibrations.my question is for some specific parts,like BBPLL VCO or RF synthesizer charge pump,shoule I first calibrate them or...
View ArticleRe: ADIS16209 Accuracy Problems and Assembly issues
Dear Mark,We have tested the values of the registers you had asked for:We got 0x3F51 in PROD_IDI and we got 0 and 0 in 0x1C and 0x1E. We are in a time pressing situation and we are no closer of...
View ArticleRe: trouble compiling with Blimp ADV7625 OSD IDE and Emulator
Hi Ron, We will look in to the problem by checking all the steps that you have given. Please let us know what is the Blimp version that you have been using. Best Regards,Jeyasudha.M
View Article[ADV7611] ABSOLUTE MAXIMUM RATINGS of "SCL/SDA Data Pins to DVDDIO" on...
Hello,I have a question about ABSOLUTE MAXIMUM RATINGS of ADV7611.There is a following description about ABSOLUTE MAXIMUM RATINGS of "SCL/SDA Data Pins to DVDDIO" on datasheet...
View ArticleRe: BF607 SMC Timing
Hi, Could you please confirm how you are measuring the AMS time? I believe you are doing so by probing the signals, and capturing on the oscilloscope. Could you please share the respective screenshot...
View ArticleAD9361 RX capture file save
Hi I am working with AD9361 FMCOMMs2 Zed board. I faced several issues need to resolved. 1. The ADI IIO oscilloscope gets hanged several times while working with it. 2. While validating RX performance...
View ArticleClik here to view.
ADSP-CM403
What are differents between ADSP-CM403FBSWZENG with ADSP-CM403BSWZ-CF/EF/FF?
View ArticleRe: Too much THD with MIXER on ADAU1701
Bob, Spot on! The cause of distortion is somewhere in the hardware. The 1701 EVB board works fine as tested. We've isolated the dsp itself and tested THD and its fine. Thanks for the suggestion.as...
View Article
