Clik here to view.
is zed output data timing to ad9364 right
The figure shows the output timing when use zedboard transfer data to fmcomms4.The sdk software use the file no-OS/ad9361/sw at master · analogdevicesinc/no-OS · GitHub but AD9361_InitParam...
View ArticleRe: ad-fmcomms1-ebz programming FPGA
hello sir..I have followed the instructions as told by you in the following link using VIVADO...
View ArticleUsing SD card in BF609 through bare metal programming
I want to use SD card to store data for an image processing algorithm using bare metal programming in BF609 EZ KIT. How can it be done.Support I want to run PEC code that comes with BF609 EZ KIT BSP,...
View ArticleClik here to view.
what is the latency of each PVP block, frame size it can process? operating...
I was going through PVP of BF609 and couldn't get the following information in BF609 Hardware Reference Manual.What is the frame size that each block in PVP process?What is the latency of each block of...
View ArticleClik here to view.
2015080- Anveshan 2014
I m trying to simulate this circuit in ADIsimPE. But i m getting the following error. "*** ERROR *** Cannot find DC operating point - No convergence in pseudo transient analysis" what does this error...
View ArticleRe: hi.in ADI Water Analysis Solution for pH Meters.pdf there is a block in...
hi erbi i think there is aproblem with this scheme using for the source of current because most of water conductivity meters have the impedance of 2000 to 3000 Mohm and they can be to about 100 Mohm or...
View ArticleThe measurement conditions for the settling time of a current DAC
Hi The settling time of a current DAC is depend on output op amp feature.For example, AD5546 datasheet say it was using AD8038.But I can't see the measurement cuircuit or external condition.Is it No...
View ArticleClik here to view.
ADP5090 User Guild Question
Dear Sir:I Study ADP5090 UG-708 "EVAL-ADP5090 User Guide" document. The Figure 4. ADP5090 Pin 4(R7) show NC But Table 2.Bill of Material show R7-Resistor, 20k. Which one is correct? If R7 is NC ADP5090...
View ArticleRe: Modifying debug_nets.ltx file
Thank you very much and for others ;This will provide you a little bit more comfortable. make it into .tcl file and add it on menu. (you have to open h/w manager first) connect_hw_server -host...
View ArticleRe: build AD9467-FMC project in vivado
Thanks Dragos for you reply, just question: can I bypass the axi dma and capture data directly from the adc to the PL, as all my design runs on the PL of zynq soc, any such example? thankskhaled
View ArticleRe: AD-FMCOMMS3-EBZ Crystal
Crystal phase noise performance data as well as other device parameters are available from the crystal manufacturer, Epson.
View ArticleRe: ADP5090 User Guild Question
Dear TWN, Thanks for your feedback. The R7 should be 20kohm on the EVB. The MINOP function depends on the resistor. The MINOP bias current is 2uA. If the voltage of the MINOP pin is above the CBP...
View ArticleChanging filters in real-time using I2C or SPI
Hi,We have the ADAU1452 eval board. We use Sigmastudio to build and upload some filters and store these in the EEPROM. It was very simple to get this working. But… We want to dynamically adjust filter...
View ArticleClik here to view.
About external delay (SPI RAM Delay) in ADAU1452
hi, About "external delay" in ADAU1452,how to use the module(SPI RAM delay )? How about Setting the Master Control port Properties？Best Regards,yang.
View ArticleRe: relationship between internal PLL and MCLK input for AD1937 ?
This question was answered here:https://ez.analog.com/thread/44482
View ArticleRe: AD5270 SDO readback line skew/timing issues
Hi Mark, Though this isn't exactly CPOL=1, CPHA=0, we have tried holding SCLK high until right before CS goes low, and then used normal CPOL=0, CPHA=1 shown in the picture. Both results were the same....
View ArticleRe: ADAU7002 interface to GSM module
Hello Thomas, Sorry I missed your second question. The ADAU1772 will generate the clock for the digital mics. So no need to supply a different clock. There are register settings to select from a...
View ArticleRe: ADE7878 AVDD DVVD error
Hi Bhanuka Which crystal standards, from the datasheet, are you talking about? The datasheet recommends a 16.384MHz crystal only. Are you talking about the crystal parameters like ESR, drive level,...
View ArticleRe: ADE7878 AVDD DVVD error
Hello Hmani,Yes. parameters like drive level and ESR. I couldn't find a crystal with those parameters.http://www.farnell.com/datasheets/1497894.pdf Thank YouBhanuka
View ArticleRe: ad9361_init : Unsupported PRODUCT_ID 0xFF
Hello Dragos, did you solved the problem?I have exactly same error in exactly same conditions. ad9361_init : Unsupported PRODUCT_ID 0xFFad9361_init : AD9361 initialization error I have tester the...
View Article
