Using external spdif tranceivers with ADAU1452
Hello, My questions pertains to clock connections on the ADAU1452 when using external spdif transceivers. My design requires 2 spdif inputs and outputs to be processed by the ADAU1452. I have elected...
View ArticleRe: AD8250 Reference Drive
Hi Ahmet, Thanks for including your schematic file. I will check your circuit and get back to you soon. Thanks!Kris
View ArticleClik here to view.
ADIS16365 accelerometer null bias issue
Hello Sir, I am ADI FAE now supporting a ESP project, where ADIS16365 is used as benchmark to test ADXC1501, both ADIS16365 & ADXC1501 are placed & mounted on the same object, the signal chain...
View ArticleRe: ADuM3150 datasheet
Hello, MSCantrell-san,Thank you very much for your prompt reply.I understood that. Best regards,Sofy
View ArticleADV7480 without audio output
Hello In my project,I use the ADV7480 as the hdmi sink.But I can't get any audio .The video is ok.I found that the LRCK=17.47k BCK=1.12M For question:1.Is it the problem of source's CTS&N value(I...
View ArticleClik here to view.
Re: ADAU1761 Problems: PLL and Alias
Hello Philipp, The 1761's versatile PLL allows using a MCLK range from 8 to 27 MHz while maintaining a core clock of approx. 45 to 49 MHz. When the PLL is in use, the core clock is always...
View ArticleRe: AD1974 Daisy-chain mode
Dave, Point taken on using the CLKOUT to drive my clock buffer. I have used the XTALOUT before in other designs and may have gotten away with it in a less critical situation. I was afraid If I used the...
View Articlebit SMACK value behavior for BF609 CAN in hibernate/resume
Hello, For the built in sleep mode for CAN, the HRM says, "Once this mode is entered, many of the internal CAN module clocks are shut off,reducing power consumption, and the CAN_INT.SMACK bit is set"...
View ArticleRe: Query about AD8497 Output
Hi Wayne, When you use single +5V supply, the output saturates at around 25mV which would be read as 5 degC. The datasheet suggests lifting the REF pin voltage to keep the output from saturating when...
View ArticleRe: ADE7763 and AD8479 isolation
Hi xmas79Before going over the schematic recommendation and possibility of using AD8479, I want to understand if you have considered current transformers for current sensing. Are you expecting to...
View ArticleRe: AD5791 output conversion to differential
Hi I am facing same question. Can I use a OP as inverter-follower to get the negative output? For reason of cost we don't want to use two AD5791s Donald
View ArticleRe: AD9650
Lasse,The input voltage can exceed the operating range but must always stays within the Absolute Maximum Range. Beyond the Maximum Range the ESD diodes will become active and could damage the device....
View ArticleClik here to view.
Boot mode retrieve problem?
Hi All, we are using Bf527 ez-kit.we change Boot Mode default to another Mode.then we set default Boot mode but they not working. i mean LED's are off state ,but Lcd screen only ON...
View ArticleUART line status register
I am using DMA transfers to receive an unknown amount of data over the UART0 of an ADSP-21489.To get around the variable length issue I'm trying to use a line break on the UART serial port to frame my...
View ArticleRe: Unable to run Decoder demo code.
Hi Dave,DaveD Do I have to move this one to Black-fin group. If so can you help me in moving Sunil
View ArticleRe: ADV7533 support 1.2V signals MIPI data input
Hello, in this initial stage, would you mind telling me ADV7533 can support this request or not by private mail?next step, I will let customer to go NDA process and contact with local ADI guys.Thank...
View ArticleRe: AD 9364 FMCOMMS2 ZC-706: How to read back DAC samples
For FMCOMMS4, we are setting the two flags to zero i.e two_rx_two_tx_mode_enable and two_t_two_r_timing_enable. I suppose that should care of selecting the right rate for dac_valid. I am not sure why...
View ArticleRe: [Need emergency help]: Many OsdApis can not be compiled successfully...
Hi Xu tao, Let us look in to this and update you shortly Best Regards,Jeyasudha.M
View ArticleRe: ICE-100B getting heat and unstable
I didn't get helpfull inforrmation.ICE-100B is obsolete device but circuit is still secret.
View ArticleRe: New design tool for simulating microphone beamforming arrays.
Hi Jeradl,Thanks very much for the tool, its very useful to me !Right now I need to design an endfire array system (in the 1140 app note), based on two ADMP504.I recently saw a video on...
View Article
