Re: Queries about Hittite X-band 500W PA KHPA-0811W
Wayne,I can not answer your questions publicly. Please email me directly regarding your application.Best regards,Mikemike.scott@analog.com
View ArticleRe: About Hittite Xband HPA KHPA-0811W efficiency curve
I can not answer your questions publicly. Please email me directly regarding your application.Best regards,Mikemike.scott@analog.com
View ArticleRe: Video decoder for SD RGB with SOG & no CVBS
STANAG 3350 Class B is PAL. I'm looking for the exact PAL version. Rohde & Swartz makes test equipment specifically for STANAG video. We are using custom STANAG video generation equipment.
View ArticleRe: Can we make ADV7626 just pass the AV mute ON to sink without sending...
Hi Leon, When I tested EVAL-ADV7625-SMZ X2.3.2 in non-mux mode, when the ADV7625 received AVMUTE in GC packet, it transmitted AVMUTE in GC packet. It also blanked the video, which is okay, also. -Matt
View ArticleAD7147 floating pins
Hi. I am currently evaluating the AD7147 for use in one of my company's projects.In the datasheet (revision D) it says on page 19:"Eachinput pin can be tied to either the negative or positive input...
View ArticleRe: SPI Transmit in slave mode
Hi Klaus, I just saw your reply now and had arrived at the same conclusion having returned to reading the hardware reference to see if I missed something. And indeed I found this on page 15-14 which...
View ArticleRe: AD8302 voltage dips
I would try increasing C2 and C8 as well to .47uF (or bigger). There is a lot frequency content on the phase detector output that needs to be filtered out to make a DC level.
View ArticleRe: Video decoder for SD RGB with SOG & no CVBS
My understanding is that "PAL" is a composite video signal, not component. By "PAL", I assume you mean 625-line (576i) at 50Hz. -Matt
View ArticleClik here to view.
Re: Sign of reactive power - ADE7878
Hi Lars, Looking at the document, there seem to be some issues. On page 1, you are showing a current vector lagging a voltage vector. Then below, on the same page, you show the actual waveforms where...
View ArticleRe: AD9361 configuration
I already read this docs, (maybe i misunderstood something but i read entire page twice..)
View ArticleRe: AD8232 not outputting any signal
Hello James, Soldering lead-less packages can be tricky. Have you tried washing the board after soldering? There are several components that are high resistance value. Make sure there are no evident...
View ArticleADRF6518-EVALZ Board Software Issue
I purchased the ADRF6518 Evaluation Board and am having some problems. I installed the software from Analog on the webpage for the ADRF6518 and I believe that I got the drivers installed correctly,...
View ArticleRe: ADV8005 Composite and SVideo Outputs
Has the customer licensed the source code for our ADV8005 software driver? It supports composite video output. -Matt
View ArticleRe: ADRF6518-EVALZ Board Software Issue
If the GUI is booting up when the USB cable is connected to the board, it sounds like you got the software installed correctly. From the screenshots, it looks like the part is not powered-up. Is this...
View ArticleRe: As for replacement from HMCAD1512 to HMCAD1511
That's good news! Many thanks Tony-san.
View ArticleADE7758 MEASUREMENT TIME
Hello All; İ am planing to use ADE7758 to make 3 phase compensation panel. i would like to learn what is the minimum time to take measurement of Active and reactive power, rms volt and current for each...
View ArticleRe: AD8368 Dangerous Startup Transient
This transient has to do with mainly the output centering loop. There are some other loops that have to settle as well on start-up conditions. A switch would probably be the easiest and best solution...
View ArticleClik here to view.
Re: ADuM3223/4223 Fundamental Questions on operations
Hello RSchnell, Thank you very much for your answer, and it is enough at this point in time. I will check and compare each parameter to parameter of ADuM3223 with this competitive part. Thank you again...
View ArticleRe: AD9102: help with /TRIGGER programming
Hi Larry, Thanks for your response on this. I changed register 0x20 to 0x000E and everything started working as expected.Maybe this is yet another item to be added to the AD9102 documentation to...
View Article