Re: ADG508 in a convection oven
Hi Maxim, Do you know what temperature the switch was exposed to? The T version of this part is rated up to +125C. The K and B versions are only up to +85C. Regards,Eric.
View ArticleRe: ADAU1452 How to use the SafeLoad mechanism
Hi John,thanks for the detailed answer.I must apologize it was my fault. The sendbuffer for the target address was not correctly initialized.Anyway your analyzer data helped a lot to find my stupid...
View ArticleRe: External Reference Issue
Hi Jerediah,I modified my FMCOMMS5 for external reference input.I had to remove C348 as well since it shares the same pad with C301.I can see the same things for REFin CLK < 15MHz.Everything above...
View ArticleAD9625 Register Configuration + Linux
Hello,I´m working with the AD-FMCADC2-EBY FMC BOARD connected to a VC707 board.The reference design works fine with the remote oscilloscope test program, but right now I am trying to control the ADC...
View ArticleRe: AD9361 FDD TDD Mode Switching
We uploaded a new update. It'll improve TX QUAD cal. But nothing related to this. Reading the ensm_mode attribute does not necessarily return, what's written to!There is no STATE called pinctrl*, ......
View ArticleRe: ADV7842 Auto-Detect
I now have SYNC_CH2_VS_SEL and SYNC_CH2_VS_SEL both set to IN1. However when I read back STDI_DVALID_CH2_RAW it is always 0. Anything else that still may be wrong?
View ArticleClik here to view.
Turning on LEDs on the ADSP-21364 EZ-KIT Lite development board in C language
Hi i'm new to programming SHARC DSPs and I have recently acquired an ADSP-21364 EZ-KIT Lite development board for my university project. I'm hoping to do some effects processing later on but for now...
View ArticleRe: Issue with Linux Nano-Distribution on Zynq (with FMCOMMS2)
Hi, I downloaded the image that you linked and a lot of the files in there have a size of 0. Including /sbin/init and /bin/sh, which explains why they can't be executed. So it looks as if the image is...
View ArticleRe: ADUC7061 - Boundary Scan Support?
Simple answer - NO, because of noise and die size.
View ArticleRe: ADuCM360 ADC0 Counts Decresses Gradually
Basically this looks ok, but what is your signal source you measure, how does the layout look like and how stable is the power-supply?
View ArticleRe: AD9910 Parallel port
Hi, Thanks for the reply. I am using the AD9910 eval board(REV G). By Parallel data port enable I'm guessing you mean TxEnable. I didn't synch the FPGA clock with the DDS PDCLK because I just wanted to...
View ArticleRe: DC/DC design using ADP1046
Hi James, Input voltage dynamically varies between 9V and 14V. Is that no problem with DC/DC implementation with ADP1046? I would like that to be confirmed one more. Regards,Mack
View ArticleRe: [Important]ADV7626/ADV7625 OSD BLIMP
Hi Owen Feng, We have estimated the memory calculation for our OSD Demo project as follows. Total Program Memory - 76KBTotal Data Memory - 37 KB Please see the attached XLS file which will describe...
View ArticleRe: AD9910 Parallel port
In the first sentence of your original post you make mention of "reading" the DDS via the parallel port. Just to be clear, the parallel port of the AD9910 is "write-only". The intent of the parallel...
View ArticleRe: AD9910 Parallel port
Hi KennyG, Sorry about the first sentence. I meant read the values from the FPGA. Regarding the parallel port, that is exactly what I want it for. I want to generate really quick (arbitrary) phase...
View ArticleClik here to view.
We need to increase the number of semaphores to open sockets for UDP.
Hello,We are developing a VoIP system using CrossCore and IwIP on BF609. We need to increase the number of semaphores to open sockets for UDP. We couldn't find how to increase that number. We get the...
View ArticleRe: Possible ways to terminate iio_buffer_refill early?
Why not do the data qualification on the remote side? It might be easier... But this is something that might be solved in the future via some metadata discussions Lars and I were having today (heavy...
View Article