ADAU1701
My application requires real-time control of General 2nd-Order Filter coefficients to change f0.Can I use Safeload registers to do that?How? Best regards
View ArticleClik here to view.
SHARC Library
When compiling -- you can generate code for any, none, 0.0 and 0.2However when you link, there are only 21469_rev_any and 21469_rev_none library directory.How do the code option match with linker...
View ArticleRe: ADE7880 - Energy measurement
Hi r.simoncelli@antgroup.it The line cycle accumulation procedure seems to be fine. But I have another question. What is the value set to in ZXSEL bits of the LCYCMODE register? This selects the phase...
View ArticleRe: Latest U-Boot for BF537-EZkit silicon rev 0.0
1, it's not officially supported, nor is it tested.2, yes, please go ahead to remove the CPU, it's verified.
View ArticleRe: Loading uClinux on bf527
Hold on a moment, I am going to have a run and share you it today.
View ArticleRe: The 2011 release compilation
could you run "make 2>err_log" on your newly built system, with the ADI default configuration and attache the generated err_log file here.
View ArticleRe: AD7190
Hi frankd, We are looking into this. We'll get back to you as soon as possible. Thanks and Best Regards,Chris
View ArticleRe: If ADN4612 can both support 1.25G 2.5G and 10G ？
Hi Dave, I want to know how about the through via can effect the signal integrity, if it has two through vias in less than 10 inch transmission line. Because the ADN4612 spec just said that Blind or...
View ArticleRe: Calibration setup ADE7878
Hi Baex Have you seen this calibration document :http://www.analog.com/static/imported-files/application_notes/AN-1076.pdf? This must answer most of your questions. But the bottom line is that you...
View ArticleRe: Simulation software and a library for ADN3000-06 ic
Thank you so much for the information
View ArticleRe: Jitter in Vsync ,Hsync at the output of ADV7184 videodecoder
Hi Rajesh, our 3D comb decders are not qualified across that temp range. Its not to say that it wont work it just means that it was not part of our qualification process.
View ArticleRe: ADE7880 Harmonic Calculations at different frequencies
Thanks Dlath, Is there any solution by which i can get harmonic calculations faster?and what are the frequency bands for SELFREQ as 0 and 1 to get more accurate readings?
View ArticleGround plane for multiple DACs/ADC
Hello, I'm designing HD soundcard based on two AD1955 in dual mono + cirrus logic ADC and I have trouble with grouding and ground planes. There are analog and digital ground and I don't have any idea...
View ArticleRe: How to implement Adaptive Filter in ADAU1701 .
Hello Charles, It seems like things that are trivial in C are often difficult in the graphical environment. For example, it is possible to search through a short delay for some event (such...
View ArticleAD7814
Hi, According to the silicon anomaly, dummy read is required.After dummy read, How many seconds is waiting till the next read? How many modes does AD7814 have? -normal mode-shutdown mode-automatic...
View ArticleRe: ADSP-BF609 uClinux buildroot make error
I use make 2>err_log ,the conten of this file is as below:wk: cmd. line:2: (FILENAME=/usr/local/blackfin/buildroot/linux/linux-kernel/include/asm-generic/errno.h FNR=113) fatal: cannot open file...
View ArticleClik here to view.
ADSP-BF609 uClinux buildroot make error
Hello，when I use bf609 buildroot ,find two errors,such as follow.The gcc cross tools,u-boot and buildroot are download from analog web:blackfin-toolchain-2012R1-RC2.i386.tar.bz2...
View ArticleADAU1461 INPUT 9 bug in SS 3.8
Hi. When trying to use input 9 (TDM ch 8 on the ADAU1461) in sigma studio3.8 i get an error on compile download."Error in Input1Line Numer 30"digin_9" variable used is not defined in RAM or not a RAM...
View ArticleRe: ADV7623 OSD flicker
Sally, We fixed all of our OSD flicker problems by waiting for the vertical blank (vblank) before updating the text. - Chris
View Article
