Re: OS requirement for FMCOMMS 2EBZ
1. No it's not 2. Yes3. Look at page 10 in this document: http://www.xilinx.com/support/documentation/sw_manuals/xilinx2013_4/ug973-vivado-release-notes-install-license.pdf Charly
View ArticleRe: AD9361_Initialization
Hi timo, we are working on AD9361 by using Spartan 6 FPGA.Can you please help us how to approach and sequence to perform one channel RX operation?To configuration of One RX what are all steps need to...
View ArticleRe: Output from AD9747 to external transformer
Hi Kaos - If you connect teh center tap of your transformer directly to ground and remove teh 100 ohm resistor you will have the DAC ouput balun circuit we used to characterize AD9747 performance....
View ArticleRe: Oscillation with AD8137
UweBonnes, Exchanged a few emails back and forth w/ the PL apps engineer. Several things. He pointed out that witha noise gain of +11, the output noise is dominated by the voltage noise, not RF....
View ArticleRe: ADAS - 112x series, current-to-digital ADC
This product is under NDA, so please contact us through a local sales channel (from where you obtained the Eval board) for any support questions on this. Regards,Maithil
View ArticleRe: Magic 15V on output pin B AD8599 and AD4075
Graeme, Give me the name of the ADI person that told you "... did ask AD and they said it would be fine..."and I will have someone in the amplifier group educate them. If you want to build one...
View ArticleClik here to view.
Re: Magic 15V on output pin B AD8599 and AD4075
Hi Harry, I was working with coleman in the dsp section, this kind of electronics is not my strong point, my area is passive crossover design 17 years of high end audio in fact and i took a lot of what...
View ArticleRe: Amp01 single 9V battery supply ... problems
Harry;The A/D Amp01 circuit is same as in the A/D data sheet for the Amp01. Only difference is that it is powered by 1 single 9V battery. Across the battery are two 100K resistors (in the shape of a...
View ArticleRe: ADV7513 problem running at VGA 640 x 480 input.
Dave: Thank you for your response. I have used that script (and many others posted) in an effort to get things working. I listed the values that I came up with in my original post. Do these look OK?...
View ArticleRe: Magic 15V on output pin B AD8599 and AD4075
gr4eme, Bummer..... We each have different skills..... Would have been good to have one of the local FAEsor DFAEs that is a generalist or an analoger look at it. I have attached a PDF that I think...
View ArticleRe: Magic 15V on output pin B AD8599 and AD4075
Harry, Im not understanding this part Your schematic does not match the schematic given to you. The B section has no feedbackbecause the B output goes through the 4k75 resistor to the output of the A...
View ArticleClik here to view.
Re: Magic 15V on output pin B AD8599 and AD4075
Hi Harry, Does this look right now? Graeme
View ArticleRe: ADP1048 eval board questions
The reference design for the 300W Bridgeless PFC is only available as a paper design in the PRD and not available to order boards. We would be more than happy to share the gerber files with you and the...
View ArticleRe: Amp01 single 9V battery supply ... problems
photodetCALIB, During my 35 years in applications, at both National and now at ADI, I have found that it's difficult to solve a problem that is incompletely stated. There is always something that...
View ArticleRe: ADIS16210 accelerometer resolution
Original post>... and, please, put the proper information in the documentation. It is not fair. NevadaMark>>This was mentioned in my previous reply, but to address this specifically, the...
View ArticleAD5930 Gotcha's
Given a recent 'fight' to implement a saw sweep from 2285Hz to 3000Hz over a 150ms period with a 1.544MHz clock, I figured I would share my insights for anyone else who may encounter similar issues. I...
View ArticleRe: ADV7403 CVBS-525 signal shows too much jitter
Hello Wolfgang.We too use ADI video decoders ADV7184 and ADV7403 and too we have a similar problem for NTSC 525i mode (http://ez.analog.com/message/44300#44300).Decoder output signals jitter arises,...
View Articlethe ouput power of AD9957 evaluation board
Hi, Here I have a question about the AD9957 evaluation board. How can we improve the power of the output of DAC on the board? Thanks very much!Best Regards!
View ArticleRe: ADAU1442 Input ASRC Clock problem
What is your "start pulse source" set to (in "dsp registers modes 1" tab) ?Is your serial output a master or slave?
View ArticleRe: AD620 drift
Harry, Yes 305uV. It is measured at the A/D module. It is complete analog module. Panasonic AD8VI. Used as a module in a PLC rack. I check values from HMI device. At pages 6-3 and 12-3 there is info...
View Article
