ADE7913 in unipolar (DC) configuration ?
Hi, We are interested in using the ADE7913 to measure unipolar (DC) voltages. Can you please advice if it is possible to get the full 24 bit resolution, and what wire is connected where to achieve...
View ArticleAD9361 Loop Filter&Charge Pump configuration
Hello, How can I configure the right Loop Filter component & Charge pump values?My system is working at 2-3GHzI need lock time of 100usec.
View ArticleRe: BF527:Using GPIO to interface NAND flash
Hi Minnu, Sorry for the delayed response, you may directly use NFC of BF52x to interface NAND flash devices instead of using GPIO or EBIU. The BF52x processor NFC supports SLC NAND flash devices...
View ArticleCan't insert an image
In EZ discussion replies, the "insert image" camera icon is dimmed & I cannot insert anything. I'd show an example except can't do it here either. Best regards, Bob
View ArticleRe: ADAS1000 Power Supply Adapter
Hello Tapan, I can confirm that the adaptor that you have received (Friwo) is the correct adaptor which ships with as part of the ADAS1000 evaluation kit. This adaptor should provide the +5V required...
View ArticleRe: AD-FMCOMMS1 and QAM1024/4096
Hi, The FMCOMMS1 transmits and receives raw I and Q samples. The modulation scheme that is used for the payload data that is transmitted is outside of the scope of the FMCOMMS1 and needs to be...
View ArticleRe: Re: urjtag: what parameter for initbus when working with BF506-based...
Great! Thank you very much, the reset option worked! Considering that this thread became too long, and that I don't have any other serious issues with this right now, I will mark it as answered.I'll...
View ArticleClik here to view.
Re: Can't insert an image
Sorry for any inconvenience this may have caused you. Please try now and let us know. Thank you.
View ArticleRe: FMCJESDADC Reference Design for ZC706 Missing Files
Hi, You have to generate those files manually, you can find an instruction how to do that here, under section "Generating Xilinx Netlist Files" Thanks,Istvan
View ArticleRe: EVAL-ADV8003 OSD Entry Point?
Ok, thanks for the information! I was hoping there was a way to avoid recompiling and updating the processor code anytime we changed the Blimp project for the evaluation kit. For example, perhaps...
View ArticleRe: ADV7393 VESA format
Hello, I'm not sure what else to tell you. As I said above NONE of our video encoders can display any VESA formats. Dave
View ArticleRe: Re: AD9361 GR-IIO
Thanks for the example, I am connecting up the source block like that. Unfortunately the diagram doesn't seem to be working - the audio out is just a random signal, and when I try to look at the...
View ArticleRe: ADV7182 Software Driver
Hi Chai, I'll check but I don't believe there are any software drivers for ADV7182. Only register scripts. Dave
View ArticleRe: ADV7625 RXE_HPA pin
Yes, hardware manual, section 6.5 speaks of an on-board 1000 Ohm resistor on the HPA pins.
View ArticleRe: can adv7850 support 4 edid maps for all 4 hdmi ports?
You aren't turning off encryption. You are just causing the HDCP engine not to be able to read the keys because you'd corrupted the internal memory address of the keys with that bit so when a source...
View ArticleAccess to FLASH memory via DMA channel
Hello, dear colleagues! Could You clear me next item– what is reading rate from FLASH memory to CPU, using DMA channel (or reading time)? This question is related to processor throughput: if the core...
View ArticleClik here to view.
Re: When I use IAR "download and debug" ,IAR stoped at "programming flash...
Check that the JLINK / JTAG is set to connect during reset and check the rotary switch is set to 1.
View ArticleRe: Re: Programming the ADSP-21479 in assembly language
Hi Craig, the linker error I was getting was related to the CRT_HDR definition being commented out but appearing later in the code segment I had posted. Commenting out the segment as well solved the...
View Article