Re: Flash programming in ADSP21489
Do you have the Boot Mode pins set correctly? For parallel flash BOOTCFG0 is LowBOOTCFG1 is HighBOOTCFG2 is Low Al Clark
View ArticleFMCOMMS1-ebz - Bandwidth tech spec. clarification
1) I'd appreciate a clarification on the tech specs for this device. On the product details link FPGA Mezzanine Card for Wireless Communications | Analog Devices> Specifications & Features >...
View ArticleRe: Impact metrics -- what?
Hi Bob, I put a document here for you FAQ: Impact Metrics Explained. There are several others listed within this one. Let me know if you have any more questions. Regards,Carol
View ArticleRe: Anyone else having an issue with IAR 7.20.2?
Hi every one , I want to test some Brushless DC Motor control algorithms made in simulink with Boston engineering Flex MC kit and Analog devices CM408F processor. Please confirm...
View ArticleRe: FMCOMMS2 Reference design Clock Question
Hi Lars, Thanks for the clarification, much appreciated. Regards Walter
View ArticleRe: ADV7630 SInk hotplug issue
Hi, Matt, becasue the customer project is in PP stage now, the issue is really critical, could you help to double check it with ADV7630 product expert?? Thanks for your help!!
View ArticleClik here to view.
Re: Building SD-card image for no-os reference design!
Hi Jet, It can be done. To do it I would suggest you use the 2013.4 Vivado tool chain as I think the ADI HDL code and associated tcl scripts were developed using this version. Otherwise you need to...
View ArticlePVP - THC0 Coefficient updated on-the-fly But not took effect.
Hi, I am using CameraPipe PVP as below, EPPI0 --> IPF0 --> THC0-->OPF0--DMA46Its working properly But if I update THC_MINTH or MAXTH register in running time, the change not affect the...
View ArticleRe: Questions about AD9279 Reference Design
1 sample = 16bits (of 1 channel). If you are not reading the DDR data the same as what you see in chipscope, it may be a need a cache flush (search for microblaze flush or invalidate cache).
View ArticleRe: ACP and ISRC support in SPDIF format
Hi Sandeep, I don't either-- but if it's in the original source data stream, then it will come out of the ADV7619 as well. Dave
View ArticleRe: SPI slave select in Software control
Hi Anand, If you refer to the Parallel Peripheral Interface chapter (Chapter 11) of the BF538 Hardware Reference Manual it explains that "The state of PPI_FS3 depends completely on the state of PPI_FS1...
View ArticleRe: continuos conversion mode in ad7195
Hi Reinhard, thanks for your reply.1) Do you always wait for DOUT/RDY# falling, before applying 0x58? Yes, I'm sure Ialways wait that the line DOUT/RDY goes to low before send 0x58.2)Do you capture...
View ArticleLimitations of using AD8352 amplifier with AD9434 ADC?
Hi Everyone, Are there any limitations of using the AD8352 amplifier with the AD9434 ADC? They are shown together in the ADC datasheet, but now the website for that part recommends a newer amplifier,...
View ArticleADUM3200 Working Voltage Specs?
I have a customer that is looking for a digital isolater, 2 channel, 1 input and 1 output. - Powered from 5V and 3.3V - The working voltage must be at least 1200VDC. - It must support a UL creep-age...
View ArticleADXL343 standby mode
Hi,I want to use the ADXL343 accelerometer in a design that needs very low power and I am wondering if the interrupts can work in standby mode? In the datasheet, I can read that no measurements are...
View ArticleRe: Dose ADI have detailed document for ADradioNet?
Hi MMA, Thank you very much for the quick reply. The attached document does help me a lot!I'm looking forward to the launch of the community for ADradioNet. How could I find this community then?By the...
View ArticleClik here to view.
Re: ADXL343 standby mode
Hi Nicolas, The interrupts will work only in measurement mode. For low power requirements please consider the ADXL362. http://www.analog.com/static/imported-files/data_sheets/ADXL362.pdf regards,Venkat
View Articlebuilding drivers for adsp-bf537 ez-kit lite in simulink
Hi,I'm using MATLAB/Simulink to build models for adsp-bf537 ez-kit lite but not all drivers' blocks are available in "analog devices blackfin/adsp bf537 ez-kit lite" library. so how could i build a...
View ArticleRe: Programming AD5122A
Hello, After bit of tweaking, the chip finally responded! Even though, it is supposed to work with standard I2C command, bit of fine tuning is always required. Thanks to Reinhard for helping me out...
View ArticleADF4351 Vref
Hi, Could someone help me to understand how the Vref is generated and used within ADF4351? In one of our board, Vref for ADF4351 is showing 350mV. For that component the lock detect is not going high...
View Article