Re: Timestamping of PTP on BF609
Hi all, When I "..\src\ether_loopback.c", line 608: cc0020: error: identifier "ADI_EMAC_REGISTERS" is undefined ADI_EMAC_REGISTERS *pEmacRegs; ^ "..\src\ether_loopback.c", line 608: cc0020:...
View ArticleRe: Timestamping of PTP on BF609
Hi all, When I defined the "ADI_EMAC_REGISTERS" type variable.And it appeared build error below. How can I do? "..\src\ether_loopback.c", line 608: cc0020: error: identifier "ADI_EMAC_REGISTERS" is...
View ArticleClik here to view.
Re: ADV7181D DDR_CLK_DEL[3:0] Register
Hello, Thank you for your advice.I understood that output data is not changed even if asked register is changed. I have one questions about Register. Could you tellm the register which we can set...
View ArticleRe: AD8036: need clarification on "fast rectifier" use.
Hi JinoL, thanks for the reply. Re 2: I realized after posting this question that a simple RC filter probably will not work. The amplifier will discharge the capacitor as fast as it will charge it. I...
View ArticleRe: ADA4817 spice model
Hi, Jon. According to the product owner, the 800fF is not present in the actual part. It was only added by the engineer who created the SPICE model to compensate some other responses during...
View ArticleRe: AD7793 latch up Effect?
Hi Thomas, The AD7793 can latchup if overvoltages or glitches are seen on analog or digital inputs. The absolute maximum ratings list the max voltages that can be present on any analog or digital pin...
View ArticleRe: Query about AD650
Hi Wayne, The AD650 is really a DC device. The AD650 has a settling time of 1 pulse of the new frequency plus 1 us. During this time, the input needs to be stable so that the output frequency is...
View ArticleRe: Help with split power operation of AD7176-2 EVAL board
Hi Pep, 1) You are correct in that the REFOUT pin will be at 0V when AVSS is set to -2.5V. However, the reference seen by the AD7176-2 is the difference between REFOUT and AVSS which is 2.5V. So, you...
View ArticleRe: Error pushing buf -13 when use the ad9361-iiostream with AD9361 on zynq706
Hi mhennerich, Thank you very much. Your reply is right, it's ok now. I have another question is I don't know the relationship between voltage0, voltage1, voltage2, voltage3, altvoltage* and the...
View ArticleClik here to view.
Re: Migrating from ADAU1701 to ADAU1401
Hi, Out of curiosity I loaded a project compiled for the -1701 into my ADAU1401 board and it worked exactly the same. Got audio into the ADCs, came out the DACs, and the Real-Time Display...
View ArticleClik here to view.
AD9257 Processing of the VCM pin
We are evaluating the AD9257, and concerned that the input of the VCM pin can affect the saturation performance of the ADC. We entering the following signal to the ADC in our system.・Common mode...
View ArticleRe: AD7960 misbehaves
Hi, I’ve looked up our evaluation board and JP7 was indeed connected B to center. We’ll update the user guide to reflect this. However, as I see it, with your EN settings (EN2 = 0, EN1 = 0, EN0 = 1),...
View ArticleRe: offset from ADA4528: datasheet pspice
Hi Dirk, Thanks for answering my questions. Well then, good luck to your project! Just let us know if you need anything else. Best regards,Emman
View ArticleADE7880 - how to calculate energy value on line cycle accumulation mode
Hello, On ADE7880, I use line cycle accumulation mode to get energy readings (xWATTHR / xVAHR), also I want to get instantaneous power values. The CT coils are connected to each phase, use 3-phase, 4...
View ArticleRe: FIT rate for ADuM3400
Hi DaveC, OK, Thanks I got it!I will explain this to our customer. Kaos
View ArticleRe: RGB Receiver
Hi, Mani. AD8143 is a good fit for your application but there are things to consider in using this. 1. The supply voltage should either be single 5V, +/-5V, +/-12V or any asymmetrical supply that is...
View ArticleRe: Even Odd pixel swap
Hi Guenter, Did you get the answer? My customer also have the same question. Steven
View ArticleClik here to view.
Re: Very low frequency oscillation in AD9958 DDS output
Hi, If you are using various output termination, that means you are using your own designed board.I have attached here an unfiltered output using AD9958 evaluation board. Output is set to 100MHz.The...
View Article
