Re: HMC1086F10 for Pulse Power Amplifier question?
Hi Sir , I got the response from my customer and please refer to below input condition1.Frequency: 9.0~9.5GHZ ,amplitude: 0~10dBm2.PRF: 2KHZ(0.5mS ) ,Pulse Width: 1uS~10uS @ PA: raise...
View ArticleRe: BF54x ElfPatch crushes!!!
Hi.I'm having problem with elfpatch too. I'm using Visual DSP++ 5.1.2 which elfpatch is at this address: "F:\Program Files\Analog Devices\VisualDSP 5.1.2"When I want to extract the contents of the...
View ArticleRe: AD215: is isolation voltage rating specified as continuous or transient?
Hi Wojtek, We do not have any isolation certifications for the AD215.If it helps though, footnote number 4 on page 3 of the datasheet provides some information on the isolation voltage: "The isolation...
View ArticleRe: AD9958/59 jumpers
Hi, OK and thank you for the answer, I was wrong when I write GND for Manual (W7) !
View ArticleRe: Interfacing ARM and AD8403(Digital Potentiometer)
Hi, Yogesh. Would you be able to provide the actual data that you are sending to the part? An oscilloscope screen shot would be greatly helpful. Regards,Mark
View ArticleRe: Need amplifier like OP497 but smaller size
Hi Kole, What supply will you be using? Also, I assume that since you're taking DC measurements, you don't need too high a bandwidth? Thanks, Kris
View ArticleRe: download.bat in AD9467-FMC demo doesn't load software successfully
Hi Andrew, I fixed the tar ball, please try it again. But I do not recommend to loose too much time with it. Try to use Vivado instead, the tool is much more intuitive and usable than XPS, and the...
View ArticleClik here to view.
HMC624ALP4E, flatness
Hello there, We are wondering if we can get/download the Flatness data in txt/numerical format of HMC624ALP4E, digital attenuator. There seems to have only one graph in page2 of the spec showings the...
View ArticleHMC922LP4E End of Life
Hi,HMC922LP4E end of life is announced, I used this component because this is the only differential switch I can found, that covers 1GHz-4GHz bandwith....
View ArticleRe: AD1938 MOSI line is always high
hello, I have the same problem, the microcontroller write between 400 et 500ns after CS goes low. How much is "immediately after CS" for you ? thank you !
View ArticleRe: adv8005 without BF524
hi, mattpI have the adv8005-smz board now. How can I config the video path from the JT11(HDMI IN 720P@50) to JT4(HDMI OUT 1080P@60).Is there any simple pc software to config the demo board use usb or...
View ArticleRe: Cannot capture from ADV7281-M with i.MX6Q
Hi Robert, I tried to change box border with registers 0x8B and 0x8C, but nothing changed. As in my previous tests, I see left and right borders (without any offset) and sometimes 2 pixel bottom border...
View ArticleRe: adv8005 without BF524
hi,fenghuayi看到你的新浪邮箱你应该是中国人吧，那我就用中文了哈，我使用的是stm32f系列的 arm，我的项目里不需要osd，所以也没有RAM用来做OSD.你demo板都调通了吗？
View ArticleRe: ZEDboard SD Card image Audio not working
Thank you Lars. I will test it and then mark as the correct answer.
View ArticleRe: How to use configuration file ad-fmcomms3-ebz.cfg for AD-FMCOOMS3-EBZ borad
Anybody having any idea regarding my questions.Please reply??
View ArticleRe: AD8000 amplification
Hi Dinesh, Thank you for sharing your block diagram. And base on your application, a 5V 20 MHz crystal oscillator would be good! You can refer to this link for crystal oscillator vendor that may...
View ArticleClik here to view.
AD9398 register value at register 0x61[3:0] (Audio sampling frequency)
Dear Support team We'd like to know what "0001b" means at register 0x61[3:0] (Audio sampling frequency) of AD9398(HDMI receiver).("0001b" isn't defined on the datasheet.) This value sometime appears on...
View ArticleRe: Interfacing ARM and AD8403(Digital Potentiometer)
Hi,Mark,Actually directly 16 bit i tired like (SPI->DR=0x11FF). bt the reading its very high more fluctuations,for RDAC1, data 01=520 data 02=568 data 03=610for RDAC2, data 01=529...
View Article
