Re: adv8005 without BF524
hi,mattpthe source is JT11,sink is JT4,The debug message is below,can you give me some advise?U-Boot 2012.07-rc2 (ADI-2012R2) (Jul 16 2013 - 11:21:16) CPU: ADSP bf524-0.2 (Detected Rev: 0.2) (spi...
View ArticleRe: Rotation Measurement
Thanks Venkat. Actually we are planning to use 9-DOF ADIS 16405, something that is required in other project. How would we measure RPM with a 9 DOF sensor ? 1. Would I simply read x,y,z values of gyro...
View ArticleRe: Interfacing ARM and AD8403(Digital Potentiometer)
Alawys fluctuation it will be there in this AD8403 IC if i send any data??
View ArticleClik here to view.
AD7793 internal calibration leads to seemingly random readings
Hi, I'm using an AD7793 for resistance measurements in a simple ratio-metric configuration (see schematic) with one excitation current and a reference resistor. I try to measure a 0.1% tolerance...
View ArticleAD9958 PCBZ not recognized by computer
Hi,I just bought a AD9958 eval board, connected it to a win7 32bit installed with the software. There are two independent 3.3V and 1.8V power supplies powering the board. After connecting it to the...
View ArticleHavig problem with elfpatch (lockbox security)
Hi.I'm having problem with elfpatch too. I'm using Visual DSP++ 5.1.2 which elfpatch is in this address: "F:\Program Files\Analog Devices\VisualDSP 5.1.2"When I want to extract the contents of the...
View ArticleClik here to view.
Re: AD7789 sensor 2.5V - all or nothing issue, 00..00 or 11..11
Hello, My problemwouldit notbecause Idirectly connectsthe sensor to theconverter.Do it required tointerface with aAOPmounting in instrumentationlike this: or somethingof that style. you tell me.I do...
View ArticleClik here to view.
Re: AD9833
i Kevin, I am using your spreadsheet(i.e. DDS MSB Out.xls) for AD9384 design, there is seem some bug in D2,D3,E2,E3.I attache a sample here(see below), it has two problems: 1. It indicate D2=6,D3=7,...
View ArticleRe: Using switches and LEDs AD-FMCOMMS2-EBZ kit.
Those ports are missing in your top level module - system_top.v
View ArticleRe: Confused with AD6676 SYNCINB drive voltage
The differential swing is all that matters. In any case, the constraint is only to make the tool happy about the DRC. It is a sanity check that all the I/O in a bank have the same VCCIO. It doesn't...
View ArticleRe: Confused with AD6676 SYNCINB drive voltage
Hi,I understand that XDC is a sanity check. So what are the actual voltages output on both devices. To my understanding In VC707 rx_sync_p is connected to J40 which is in an HP bank.In XC706 rx_sync_p...
View ArticleRe: download.bat in AD9467-FMC demo doesn't load software successfully
Hi Istvan, Thanks so much for your help! Andrew
View ArticleRe: Can I run 2 ADAU1701 in parallel completely independent of each other ?
Dave T, whats the down side using a VIA under the pins ? and why you would not connect the pins of the part through a via. Thanks
View ArticleRe: Audio DPLL not locked on ADV7604
Hi Matt, No, I don't have an evaluation board. I can try to find one with my manufacturer...What would be your suggestion ? Is it related to the video source ?Thanks,JM
View ArticleRe: ADUC845
Ya. you're right. As some of the load conditions that i'm still don't know. So it may take some times to measure. Thanks.
View ArticleInstallation of board support package
Hi,I'm a beginner of CCES, I tried to install the ADSP-21369 EZ-KIT BSP. However, when I wanted to make a new project, the "installed Add-ins" did not contain the BSP i just installed. Any solution to...
View ArticleClik here to view.
Re: Using switches and LEDs AD-FMCOMMS2-EBZ kit.
Those ports which vivado indicates as missing are the ports of my own design . ( LEDs and switches are named differently from analog design in order to connect to my own logic that is chained to the...
View ArticleRe: ADIS16488A SPI Communication Troubles
I think something with the Adafruit library we have on the Beaglebone is giving me some serious troubles in switching the clock polarity. I have altered several files and tried different routines to...
View Article
