How to sign an SLA and get hdmi driver
hi expert we am implementing hdmi repeater function based on adv7610, How to sign an SLA and get hdmi driver? for example, DVP_SW_7612_7611_7511_R1.53_20111021.zip
View ArticleSampling Frequency Increase in ADFMCOMMS-1
Hello,I have been using FMCOMMS-1 with ZedBoard. I am trying to implement a direct baseband sampling application using AD9643 with RF components bypassed (by solders) on the FMCOMMS-1 Board. I have...
View Articleadv7610 repeater
Hi expert adv7610 can work well on non-repeater mode, now I need to implement repeater funciton based on adv7610, i have trouble with it ,can you help me to check the flow? 1) set repeater (Bcaps)2)...
View ArticleRe: How to set the ADAS3023 to start?
Hi Lorime, On initial power up of the ADAS3023, the configuration is undefined. What configuration are you utilizing? This needs to be configure by applying reset or programming the configuration...
View ArticleRe: Sine Generator
OK. so now I know the frequencies you want, but not the purity. I would look at a "universal switched capacitor filter" chip (not sure if ADI do them though, so google it). You can connect one up as a...
View ArticleRe: ADA4940-2 noise issue
Hi Tom, The feedback capacitor extends the closed-loop bandwidth of your amplifier circuit, hence the high frequency noise will be integrated into the circuit. When the feedback cap exists, adding a...
View ArticleRe: type of interface in dds ic ad9959 to generate a lfm signal
thanks and regards to guide me voluntarily....
View ArticleRe: Driver for Windows-8 ( for SHARC USB EZ Extender Powered by the SHARC 21375)
Hi Csound, As i believe you're working with VisualDSP++ I've moved the thread from the SHARC community to the VisualDSP++ Community. What version of the tools have you installed on your new machine?...
View ArticleRe: AD5433: CS pin
Hi Mr. K, I do not fully understand the noise experiment carried out with the AD5433, could you please answer the following questions? Can you confirm that the evaluation board in use is the...
View ArticleRe: ADV212 in decode mode, 1080i-50Hz
Hello, It never stops even when it has read the complete frame. I did not modify the ADI headers in the *.dat files which had been generated by the encoders.There are separate field files without ADI...
View ArticleRe: Driver for Windows-8 ( for SHARC USB EZ Extender Powered by the SHARC 21375)
Hi David good morning. I don't use VDSP tools in my new Windows 8 machine. I want to use host application to connect with SHARC via USB Extender. In this, I need Windows 8 based USB driver for...
View ArticleRe: AD9643 - how do control the sampling rate?
Hi Cien, I'm not sure why you are still not getting an output. Just to make sure, you have populated Y501, R541, and R542 while removing C532 and C533, correct? I am also uncertain as to why you have...
View ArticleRe: ADV7619 - HDMI Compliance Test Failed
Hello, My first suggestion would be try to disable the EQ altogether for those resolutions but I'm checking to see what suggestion we have internally. Many customers have passed compliance with...
View ArticleRe: Kernel panic - not syncing: VFS: Unable to mount root fs
I tried ./build_jffs2_fs_kernel.exp BF518F-EZBRD, but that does not use the gpio-addr-flash driver. The build crashes in a different place after complaining: NOR chip too large to fit in mapping....
View ArticleRe: ADV7181D 12 bit RGB 4:4:4 DDR mode
The video standards and output resolutions you provided don't match table 10 (primary mode and video standard) of the Datasheet Manual. Table shows output resolution of 720x480 for both SD 4x1 525i and...
View ArticleCCES reset and reload does not reset SIC_IMASK registers
When I "Reset and Reload" a debugging target in CCES, the SIC_IMASK registers are not reset to their default values. Is this how it is supposed to be? Is there a setting somewhere to do a full reset?
View ArticleRe: Instrument Amplifier For Gas Analyzer Assistance Needed
AnalogGround: I am not sure about #6 in your previous reply. Can you clarify?
View ArticleRe: Diverting Low Level Audio
I`ve had some time to try and use the optimized method in my project. Purely comparing instruction used, I`m finding my original project used 929 instructions, and the new one takes 1127 (over the 1024...
View Article