problem with my ADIS16448 data output
hiim having a problem with my ADIS16448. some of the data im receiving doesn't make any sense.the pressure is 40 mbar, which should be around 1020 mbar. and the tempreture is much more higher.i sent...
View ArticleClik here to view.
Re: ADE7757arn
Actually i have bought the IC but there is no notch on the IC. I am attaching the picture. can you guide me where is pin 1 located?
View ArticleClik here to view.
Problem in output from CF pin of ADE7757 IC
I am making a digital energy meter using ADE7757, but i am encountering some problems. The output on CF pins remains constant at 17.5mV, and I am not getting any pulses on either F1, F2 and CF.. Can...
View ArticleADV7186 Full Data Sheet
Hello, I am DFAE at phoenix technologies. Meprolight, one of my customers, is interested in ADV7186 for video applications.Just a short form data sheet is available on ADI site. Could you please send...
View ArticleRe: FMCOMMS2 and Zedboard
Thanks, Rejeesh. I decided to play it safe and use ISE 14.4 and "Regenerate all project IP (under current project settings)". I then followed the instructions in...
View ArticleRe: Gyroscopes
Hi Jim,I understand where you are coming from. These sensors are often blended with independent orientation, velocity, position updates, using a Kalman filter. Without those types inputs to "blend"...
View ArticleRe: About ADV7341
RSET determine the full scale output current from the DACs. How are you changing the loading between the yellow and blue traces? Just 300 to 37.5 Ohms or is there some other buffering /components...
View ArticleRe: Inability to enter hibernate on BF504F
Thanx!I did as you advised, all works OK. I have one more question: need I config SIC_IWR* before calling bfrom_syscontrol or it I can to do it one time in calling pll_config ?
View ArticleSPORT DMA simulator problem using adsp-21478
Hi, I am trying to use the simulator for the 21478 to verify the SPORT DMA with streams. I modified one of my existing programs I originally wrote for the 21065L. Before I modified it, I checked it...
View ArticleRe: ADV7513 and bt.565 (PAL)
Just another update, Figure 5 in the SW manual maybe superfluous since 0x4A has a required write value.
View ArticleRe: ADIS 16488 changes with time
Hi, I'm very sorry for long silence. I was on business trip first and then I got distracted by other projects after return. Actually we have not tried the new mounting scheme yet, but I asked the...
View ArticleRe: ADIS 16488 changes with time
That is up to you, but I would consider starting with the washers only to start with, as it might be difficult to quantify the level of force that this material might have on the package. Establishing...
View ArticleRe: questions ADE7753
Hi Silviaing, Could you provide a schematic of your design? Including the current sensor and everything leading up to the V1P and V1N inputs. Please also send me the IRMS register values in...
View ArticleRe: ADAS1000 CRC
Hi Jim_Jim, The header is included. I have attached an example that may assist you in following how it works. Regards,Padraic
View ArticleFIR Accelerator usage without interrupt
How can the FIR accelerator be used without interrupts? In the example code, all FIR accelerator projects use a "dummy" FIR DMA ISR, even when you select "don't generate interrupts" in the expert code...
View ArticleRe: ADuM6210 radiated emissions
Chris:These are good questions.1. We discussed this here, and it may be best to keep it simple. If you can put an edge guard that cuts off the primary side of the ADuM6210 from the RF section, this...
View ArticleRe: ADuM6210 radiated emissions
Thanks for looking into these questions Brian. On our board, the RF section is away from the ADuM6210 primary side, so placing an edge guard that separates the two shouldn't be a problem. We'll give...
View ArticleADE7878 Current Transformer Question
Hello, I have a question in a project using the ADE7878, and I would like to know if you can help me. I need a current transformer with a low phase shift that can be compensated by internal the...
View ArticleRe: ADAV801: Change LRCLK at Serial Output Port from 96kS to 192kS
Hi Torsten, You can start a private conversation thread and invite Dave to join it. Click the Create button at the top of the page and choose Discussion from the list of options.Then, choose the...
View ArticleClik here to view.
ADF4158, ADF4159 software
ADF4158 and ADF4159 software attached. Compatible with Windows XP, Vista, 7 (32-bit and 64-bit). Main Controls: Ramping and shift-keying controls: Post any problems/questions below.v4.10.2: Fixed a bug...
View Article
